Pages

Tuesday, 8 April 2014

Traditional or modern control layout Part 1 Discussion

Kestrel. Panasonic GH3, 100-300mm lens. I was getting ready to make some long distance landscapes with the Mode Dial on A (perture priority). This kestrel hove into view so while continuing to look through the viewfinder, I quickly flicked the dial to S (hutter priority) which was pre set to 1/1000 sec and made 5 quick shots in the 3 or 4 seconds the bird was within range.
Nostalgia vs Efficiency ?
For a large part of the 20th Century if you had an SLR or rangefinder it came with the traditional suite of controls because there was no alternative. Cameras were mechanical. The means by which shutter speed, aperture and focus were achieved were all mechanical and the settings all visible from above the camera. In due course cameras acquired more and more electronic functions. Aperture and shutter speed repeater readouts appeared in the viewfinder. Aperture Priority then Shutter Priority Auto exposure became possible. Around the turn of the century control of auto exposure capabilities was consolidated to a single (set and see) Mode Dial with adjustments made by a mode dependent control dial. This is the basis of the modern control system which still dominates the world of DSLR's and most MILC's.

The retro phenomenon Over the last few years we have seen several new camera models released with some variant of the traditional control system, always as a hybrid with the designers trying to blend traditional and electronic controls in the one device. My work with ergonomics leads me to the view that the retro phenomenon is actually retrograde and leads to a less efficient user experience than a well designed fully modern control layout can provide.

Basic features of the traditional user interface All the user interface modules (UIM's) are of set and see type. This means what it says. The dial or lens ring has marked settings which are selected directly. An example of an all manual 1960's/70's traditional camera is the Pentax Spotmatic shown in the photo.

Advantages of the traditional UI

* Settings for primary and in some cases secondary exposure and focus parameters can be set and are visible from above the camera, without needing to turn it on and without needing to look through the viewfinder or monitor or LCD panel.

* Some users have expressed in user forums a preference for setting and viewing exposure and focus parameters on set and see dials as they say it forces them to think more carefully about their "firing solution" (ISO/Shutter Speed/Aperture) than is the case with a modern UI using a Mode Dial and Control Dial.

* Some users say they "like" the style, appearance or idea of a traditional camera. I say beware the pervasive influence of "likes", any one of which is likely to be idiosyncratic and temporary.

Disadvantages of the traditional UI

* In Capture Phase of use, when one is looking through the viewfinder, all those set and see dials are invisible. But Capture Phase is precisely when you most need to see readouts for primary and secondary exposure and focus parameters. So the makers have to provide repeater readouts for all that camera data in the viewfinder.

* So now we have a key camera data set appearing in two places. But there is a considerable opportunity cost to this. A set and see UIM can only be used for one data set. If the module is used for, say, ISO setting, it cannot be used for anything else. My ergonomic studies have led me to realise than set and see UIM's are actually most useful for Prepare Phase adjustments to the most frequently used Modes. Individual preferences vary but these would I think usually be

* Focus Mode (AFS/AFC/MF)

* Autofocus Mode (On Panasonic cameras, Face detect/Tracking/1-Area/23-Area/Pinpoint)

* Drive Mode (On Panasonic cameras, Single shot/Burst/AE Bracketing/Timer delay)

So these should have highest priority for location on camera top set and see dials. But if primary exposure parameters are on those dials the modes have to be bumped off to a Q Menu or in some cases to sub levers beneath the top dials. This can make the top deck a very busy place, not easy to read or operate manually.

* Without a Main Mode Dial you cannot have a Novice's (point and shoot) mode or Custom modes.

* There is no direct access to P,A,S, auto exposure or Manual exposure settings.

* My time and motion studies of the actions required to operate the camera in Capture Phase show that in most cases the traditional UI requires more actions each of greater complexity than is the case with a modern style UI.


Advantages of the modern UI
* Permits a cleaner layout with less UIMs required than the traditional style.

* Permits direct access to capture modes including a novice (point and shoot) mode and custom modes.

* Gives direct access to the P,A,S, auto exposure modes and manual exposure mode.

* Almost all actions required to operate the camera are carried out with fewer, less complex movements of the fingers and hands and fewer associated movements are required to enable the primary movements.

* There can be more space on the camera for UIMs the function of which can be user set. Fewer UIM's have only one function. This allows each user to effectively design their own interface.


Disadvantages of the modern UI
* I really can't think of any. The operator cannot see readouts for aperture, shutter speed and ISO without looking in the viewfinder or monitor but I don't see that as a disadvantage. That is where and when you need to see that particular data.

* Some people have expressed the idea that the modern camera looks like a lump of plastic without a "soul". Maybe it doesn't look retro chic funky cool. The top deck is not loaded with "real metal" dials. So what I say, it works better.


Next: Worked examples

 

 

 

No comments:

Post a Comment